Does anyone know where the engine number is on the 16vt? My insurance company are insisting on knowing the engine number for the engine conversion, and of course I didn't make a note of it when it was out the car.
Does anyone know where the engine number is on the 16vt? My insurance company are insisting on knowing the engine number for the engine conversion, and of course I didn't make a note of it when it was out the car.
Think FCCUK have found it for you
On the front of the engine, near/behind the turbo oil pipe.
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
1993 Alfa Romeo 155 Q4 , 2.0 Turbo
That's the one....mine seems to be weeping bit!
Saw some silicon items on ebay recently...
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
Walkers sell the Samco one too. Think it was slightly cheaper than the OEM..
1993 Alfa Romeo 155 Q4 , 2.0 Turbo
Another job to do then...
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
About ?35 inc post!
http://cgi.ebay.co.uk/Silikonschlauc...teile_Zubeh?r?
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
Thanks chaps Begbie on fccuk found it - now I've got to see if I can read it off my old build photos on a black block.
I replaced that silicon elbow with OEM, I forget how much it cost, didn't think it was that much ~?20?
It's a good job, you'll make good use of your slang vocabulary as you are trying to wrestle the stupid hose out and then back into place!
Yes...guess who forgot to put the pipe on when he was replacing the turbo and manifold?
Also, the two pipes are practically touching on my car, not sure if this is correct but it meant I had to slacken the manifold again just to swear at the pipe whilst fitting it.
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
The price above does seem a bit steep compared to these:
http://www.merlinmotorsport.co.uk/SA...d00bad1621c7d0
wrinx
My Q4 in the Garage
www.alfaromeo155.co.uk ............................ □□□-V-□□□ .................................. www.ilmostro.co.uk
I bet they aren't as soft as the OEM ones. Good because they will probably last longer, not so good at fitting time though..
The 2 pipes are almost touching on mine as well, it is very fiddly to replace the hose, but I managed it without removing the manifold and without damaging it. I did it in the summer so I guess it was a bit softer than it would be now, and when refitting use some light oil to lubricate the rubber over the metal pipe, then swear some more as it runs down the hose and you can't grip it to get the pressure on it anymore.
Last edited by AJ; 12-12-08 at 15:47. Reason: someone must have stolen some letters from my post hmmmm
How is the car running since the rebuilding after the cam belt let go AJ?
1993 Alfa Romeo 155 Q4 , 2.0 Turbo
Good thanks Jack - all 20 miles have been successful
It's not had an MOT for a couple of months, nor tax. I've had some major projects on at work and still have into the new year so I was going to get it ready to get it back on the road in March time.
I took the opportunity to lose the balance belt as well - I locked the front pulley as it would get some pick up off the bearing and eventually turn the shaft. I haven't really driven it enough to notice much difference, and now it has been so long ago I would hardly remember unless it was radically different.
I checked compression after the head gasket had cured, all returned back to normal
1993 Alfa Romeo 155 Q4 , 2.0 Turbo
Bookmarks