75w85 GL4 is the spec. I would use a full synthetic like Redline MT85.
Type: Posts; User: SteveNZ; Keyword(s):
75w85 GL4 is the spec. I would use a full synthetic like Redline MT85.
engine or gearbox?
Just looking.
Well 4 years later lookie what I came across!
https://lh4.googleusercontent.com/_aMPwGCINtyCb2ARbiRzywUzoBcnDPSPspl6gklW14M=w276-h207-p-no
These are tuning tools, they provide information to the user or, they say, to an ecu. It will not alter the timing by itself.
It's part of the Link engine management line up so I assume it can be...
Knock Link
http://www.knocklink.com/
Coupe 16VT have the same front hubs afaik, they have the same brakes. I have Koni shocks in my Coupe and they are very hard. They could be used in a heavier car.
My comment was just an interpretation of the extract above. When they say "after undersizes" they mean "after the crank has been undersized". Think about it from the automaker's point of view. It is...
No, you'll need to re-nitride the crank even for the first undersize.
What oil were you using and what is the engind from exactly? I had a 1986 Croma turbo engine but it had a different turbo.
I have the lanciahf.eu stage 1 chip in my Coupe at the moment. Designed to run on 95RON and can make up to 245hp at 1.3bar. Thats really the absolute maximum with the standard turbo. I'm not sure if...
O2 sensor and or cat
I have not read the whole thread but the Fiat Coupe has a 3.1 final drive vs the 3.3 in the Q4. If you wanted a slightly longer set of gears, use the Coupe FD! I would rather have shorter gears. 3.3...
It depends on the brake specific fuel consumption (BSFC) of the engine.
Turbos have a higher BSFC than N/A.
The rough guide was from memory 4.5-6.5cc/min per HP depending on the BSFC.
He also used very hard rear springs. That car did not have an issue with body roll.
Does the Q4 bars fit all the models then?
Are you not woried about understeer? I like to add a larger rear bar, just to make it more neutral. I have tried everything from a 16mm to a 24mm in a...
Are you getting these from Pedders in Australia? Whiteline is generaly more popular and better respected for competition suspension parts. They stock 22 and 24mm rear bars. I've seen a few fitted to...
I have come across some Alfa 166 calipers so I'm exploring a conversion on my Fiat Coupe 16V turbo which has the same brakes as the Q4.
I have Coupe 20VT wheels which will of course clear 20VT...
You could say that. But the "uno turbo/Alfa 2L" is just an evolution of the 128/strada gearbox even though the gearset is different. Some parts still interchange. There was of course an Uno turbo...
Yes that's totally different!
There are only 2 basic gearbox types to cover the whole Fiat/Alfa/Lancia range. A lot of parts are interchangeable over the years, and decades!
One gearbox started in the Fiat 128 and the other...
Really? Sorry my knowledge of 164's is very poor I must admit. The FWD versions have the same gearbox type though.
I very much doubt it. The are the same gearbox type. There is no significant difference as far as I know.
No as is. The bell housing will be different. You could possibly swap the lower casing for one from a Q4/Integrale/other.
My Pierburg seems to work fine but I have a MAC valve to use inplace as suggested by Xavier. This is a common solenoid used with many electronic boost controllers, mine is from a Gizzmo IBC. Once...