Search:

Type: Posts; User: Leo; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.02 seconds; generated 2 minute(s) ago.

  1. Which wheels clear the calipers ?

    Which wheels clear the calipers ?
  2. Thread: Q4 Quick Shift

    by Leo
    Replies
    5
    Views
    4,942

    Hi Peter, I have sent you a PM

    Hi Peter,
    I have sent you a PM
  3. Thread: Q4 Quick Shift

    by Leo
    Replies
    5
    Views
    4,942

    Q4 Quick Shift

    Hi does anybody know if these as=re still available ?
    Also anybody done any mods or upgrade at the gearbox end - my rubber bush is completely perished.

    Leo
  4. Thread: ECU Swap

    by Leo
    Replies
    8
    Views
    10,923

    I was thinking the same thing ... They also have...

    I was thinking the same thing ... They also have the cam sensor and twin coils
  5. Thread: ECU Swap

    by Leo
    Replies
    8
    Views
    10,923

    Ok but out of interest are there any ECU's which...

    Ok but out of interest are there any ECU's which are interchangeable ?
  6. Thread: ECU Swap

    by Leo
    Replies
    8
    Views
    10,923

    OK Thanks - I was looking for a quick temporary...

    OK Thanks - I was looking for a quick temporary fix
  7. Thread: ECU Swap

    by Leo
    Replies
    8
    Views
    10,923

    ECU Swap

    is it possible to switch ECU's ?
    will a delta EVO 1 WH4W be replacement for a 4w6 ? Mine is a 101.02 and it seems to be creating problems for tuners
  8. Replies
    4
    Views
    4,316

    I took mine off ... Mainly on Guy Croft advise...

    I took mine off ... Mainly on Guy Croft advise ... If the belt goes it will take out the cam belt. You make up little steel plates and it locks the shafts.
  9. Thread: Rear Koni's

    by Leo
    Replies
    13
    Views
    6,841

    Hi Peter, Thanks for your reply - I have...

    Hi Peter,

    Thanks for your reply - I have fitted the Spax to the rear and the car seems good.

    Leo
  10. Replies
    4
    Views
    4,641

    Thank you for this information

    Thank you for this information
  11. Replies
    4
    Views
    4,641

    Thanks - There is no Fiat Part Number - but there...

    Thanks - There is no Fiat Part Number - but there is more lift than the stock cam - and my rough measurements came to around 0.5mm more than the standard stock cam so that seems to make sense.
  12. Replies
    4
    Views
    4,641

    Identifying a Tipo 16v inlet cam

    Does anybody know what markings a Tipo 16v cam should have ? Mine is stamped A6 and has the numbers 466 as well as two painted bands one green and one yellow.
    When I tried to measure it with...
  13. Replies
    20
    Views
    8,003

    I bought a used rack but after taking mine out I...

    I bought a used rack but after taking mine out I decided it was too risky and had the rack rebuilt. It's a big job and I didn't fancy doing it twice.
  14. Replies
    3
    Views
    3,912

    Thanks ... The drive would be difficult as the...

    Thanks ... The drive would be difficult as the front is all dismantled ! I have the engine out now as I split the shaft at the uj. I think you are correct they seem glued or loctited on .
  15. Replies
    3
    Views
    3,912

    Just to show I'm not crazy !! 2396

    Just to show I'm not crazy !!

    2396
  16. Replies
    3
    Views
    3,912

    Problem removing propshaft

    Has anyone ever had a problem removing the props haft - I was expecting an easy job but cannot get it out - the cv joints seem to be stuck in the flanges - any ideas on freeing them off ?
  17. Replies
    52
    Views
    57,215

    Next to a proper bike I notice. :thumb:

    Next to a proper bike I notice. :thumb:
  18. Replies
    1
    Views
    3,698

    Stainless Manifolds

    Are these the exhaust manifold that proved to be no good for ours cars ?
    ...
  19. Replies
    20
    Views
    8,003

    Still thanks and that extra bit of information...

    Still thanks and that extra bit of information about reinforcing is good
  20. Replies
    20
    Views
    8,003

    That's great guys thanks for your help. Just...

    That's great guys thanks for your help. Just ordered a coupe rack ... May need to change arms and track rod end but will see when I get it .... Looks a lot easier with the engine out if the way !...
  21. Replies
    20
    Views
    8,003

    I don't mind moving mounting point but is the...

    I don't mind moving mounting point but is the gear linkage point the same ?
  22. Replies
    20
    Views
    8,003

    when I do the swap I will take photos and post...

    when I do the swap I will take photos and post here
  23. Replies
    20
    Views
    8,003

    thanks for this It's all confusing but helps...

    thanks for this It's all confusing but helps :thumbsup:
  24. Replies
    20
    Views
    8,003

    Ok thanks so 155 2.0 16v is not a quick rack or...

    Ok thanks so 155 2.0 16v is not a quick rack or doesn't fit ?
  25. have you got a picture of how the linkage works ?

    have you got a picture of how the linkage works ?
Results 1 to 25 of 47
Page 1 of 2 1 2