Printable View
My Q4 is missing the brackets that comes between the central diff and the block. I've highlighted the missing brackets using JimNielsen's foto
http://farm8.staticflickr.com/7222/7...68e52b73_z.jpg
I would be most grateful if someone could measure the thickness of those plates and are there any unusal bends in them, especially the one with 4 holes. Are they still available new and are they specific to Q4?
Hi Finn, to be honest I've not noticed those plates before. How long has your car been without them?
I'll have a dig around and see what I can come up with for you.
Steve
Maybe I've them laying within reach.
Shall have a look tonight.
If I have to guess, about 8 - 10mm thick.
Well here is a link to the parts on eper. You could always get the part numbers and see if your local dealer has a set. :rofl:
And as Brul says, I'll bet they are at least 8mm thick, any less and there would be no point to them.
Thanks for the replies. I've no idea how long it has been without them. The car stood without the engine and gearbox from 07/2009 until 01/2011 and after that it has covered only 1000 odd miles. It was put together in two months at the end of 2010 and I'd guess the brackets were left out then by mistake.
Thanks for the eper-link. Maybe I'll get lucky with my local dealer :D
They must serve a purpose as they we're put there. And I guess I'll be making my own brackets, but wanted to know how strong to make them. They look simple enough to make.
Sorry for the delay, something completly unimportand took my time yesterday.
No not the footbal game last night ;)
But took the time today and tried to make up the dimensions of the various brackets as promised.
http://i115.photobucket.com/albums/n...e/bracket1.jpg
http://i115.photobucket.com/albums/n...e/bracket2.jpg
http://i115.photobucket.com/albums/n.../bracket3a.jpg
http://i115.photobucket.com/albums/n.../bracket3b.jpg
On the last picture there's a pin or a nut in there!
Hopefully this is helpful in making your own brackets ;)
Brul(tm) m8, sorry that the dutch played shite, but your photos and measurements are brilliant :clap:
Thanks!
Will post photos once the brackets are done.
I don't like footbal, haven't seen the game(s) ;)Quote:
Originally Posted by Finn
Will measure op the holes for you later this weekend and make a picture of the pin/nut/washer for you. I just don't have the energy to go into the garage :blush:
Well it's been long time coming but these brackets are done. Would be appreciative if someone could check and photograph the pin/nut/washer assemblies on the fixings. Especially on the larger 16mm holes. Found one liner still left on one of the studs. And improvised liners for the big holes, but the brackets aren't supported sideways on every point. Only tightened and held in place with the nuts and flat washers. Pretty complicated to explain...
http://farm9.staticflickr.com/8052/8...042d2d30_z.jpg
Quote:
Originally Posted by Brul(tm)
Looks good Finn :thumbsup:
Will look them up tonight, if I can find them.
Have been cleaning the garage lately to start working on the Q4 :hyper:
Found the brackets, see the pictures below for the measurements.
Bracket with pin:
http://i115.photobucket.com/albums/n...ketwithpin.jpg
Diameter hole where the pin is located:
http://i115.photobucket.com/albums/n...e/16mmhole.jpg
Almost 16 mm.
Thickness of the pin:
http://i115.photobucket.com/albums/n...out16mmpin.jpg
A bit less then 16 mm.
Height of the pin:
http://i115.photobucket.com/albums/n...ut15mmhigh.jpg
15 mm in height.
The thickness of the "washer or top" of the pin:
http://i115.photobucket.com/albums/n...ut2mmthick.jpg
About 2 mm thick.
The diameter of the pin itself:
http://i115.photobucket.com/albums/n...indiameter.jpg
just 10 mm in diameter.
Hopefully this helps you finishing your brackets and pin.
If you need another measurement, please let me know.