Questions about parts

I wonder if these parts would fit the Alfa 155 Q4, they are for the Delta EVO originally, I have already asked the guy who runs the site and he didn´t know if they would fit the 155 as well, as he is "Only" Delta-Guru :O, maybe someone here knows?


The steeringpump/alternator bracket seen here:
http://scara73.it/motore/motor16.htm


The ergal pulley-kit seen here:
http://scara73.it/motore/motor1_2.html
personally I think the pulley for the steeringpump looks larger than on the Q4


The abarth steeringrack seen here:
http://scara73.it/motore/motor14_1.htm
would 1 turn left and right be too quick you think?

they are very nice parts, but none of them fit to 155 Q4.
155 Q4 have alternator in front of engine, lancia in the rear, steering pump is also different whole bracket is different,
pulley kit also won't fit because water pump is diferent and generators are diferent,
and steeringrack is also different....

Ok, thanks abarth 22 for your answers, I have one more question you might be able to answer:
would A engine (complete from Lancia) with steering pump/alternator bracket, water pump and generator and pulleys fit in the 155 enginebay or will there be too tight?

yes, 90% sure it would fit and leave some space, because deltas engine bay is tighter than 155. you just need to replace front down engine mount from 155 to deltas engine (aluminium one, where is oil filter). and don't know about conections of steering pump,they may be defferent between these two engines, but that's not so important.

best regards
Vedran

When I had the Rosso Q4 , the one Wobbs has got now, it came with a few spare parts from when it had the engine replaced. The new engine was a crate Integrale engine so a few bits needed to be swapped over for the Q4 equivalent ones from the old engine. I can't remember exactly what they were, but there certainly wasn't anything major.

New parts questions..

Should I buy a carbonfiber front bumper and rearspoiler -94 BTCC-style and carbonfiber mirrors as the GTA had

THe guy I have been in contact with races Alfas (mainly 155s) in The Netherlands I think, surely you know who they are, H&S Corse, he is asking about 1100 Euro for all three, is it reasonable?

give me your point of view

Wow.... A lot of money....

Sounds a lot but it depends what they mean to you.
If you really want them to create your ultimate 155 then it could be reasonable.

It would be the ultimate look of a "road" 155 in my opinion, a bit low but should be as driveable as with the silverstone frontsplitter I have had the lasst 2 summers..
But..
It is a lot of money and I have another Q4 with starting issues for the moment, read the "backfiring-thread" and help me out :huhsign: :blink:

When/If I sort the daily-drives start-problems maybe I will consider and check the bankaccount if it is possible, I do wan´t the uprated ARBs and the camshaft-removal kit as well, so a LOT of money If I want all things.. :wacko:

camshaft-removal kit ??

I think he means balance shaft removal kit :)

Well, when you are looking for the ultimate car, you have to pay a lot. I just think that for these 3 parts the price is high enough. You could make them somewhere else much cheaper

i have made kit for removing balancer shafts for 40 euros

As Steve said I ment the Balance-Shaft removal kit not the "camshaft..."

Mpampis: do you and Steve have a hunch of what the prices will be for the "GTA" bodykit you are manufacturing for your car, and when can you expect it to appear in the shop? sure I´m not the only one wondering..

Quote:

---

Originally Posted by Q4-Dave

As Steve said I ment the Balance-Shaft removal kit not the "camshaft..."

Mpampis: do you and Steve have a hunch of what the prices will be for the "GTA" bodykit you are manufacturing for your car, and when can you expect it to appear in the shop? sure I´m not the only one wondering..

---

No idea to either question from my side I'm afraid, like all good things it will be worth waiting for though.

We late a bit with bodykit. Sorry about that but we are in good way. The only thing is missing now is the front spoiler and we are reay to paint and make the rest moulds. I will post a photo in my thread from today but it is not so good one