PDA

View Full Version : New engine



Wolf66
27-12-06, 21:12
As i came to the power limit of standard engine, i installed new engine over the hollidays.

Specs:

CPS forged pistons comp. ratio 7.8:1
Colombo&Bariani street max cams
Gasflowed head
Custom made aluminium inlet manifold
Vernier pulleys
Spesso Group A headgasket
12mm head bolts
Lightened flywheel, balanced with crankshaft
Siemens DEKA 650cc injectors
Walbro highflow fuel pump
Tubular exhaust manifold
External wastegate
3" freeflow exhaust
3 bar MAP sensor
Front mounted intercooler


Max power 372 hp@5925 RPM, torque 44.2 kgm

Max power is at such low RPM, because ECU cuted the ignition at 1.2 bar boost. Real max power should be around 6400 RPM. I will dyno it again, when i'll write new chip for new 3 bar MAP sensor and 2 bar boost.




http://www.moj-album.com/slike/5884310/9ZSiNuxXKWRv4YK3.jpg

http://www.moj-album.com/slike/5884310/g8hMkne6ooXopzs6.jpg

http://www.moj-album.com/slike/5884310/mit51VZuddTQy3qt.jpg

http://www.moj-album.com/slike/5884310/djijaqtn5aGTevMx.jpg

http://www.moj-album.com/slike/5884310/0H5j9YU5uy02Ve9_.jpg

http://www.moj-album.com/slike/5884310/1eUQnv7O6PtlhxmQ.jpg

http://www.moj-album.com/slike/5884310/BStOQJb0ceUe8eI9.jpg

AlfaJack
28-12-06, 00:02
Lovely job, very impressive :) :)

oh one day mine will have that sort of treatment :twisted:

Brul(tm)
28-12-06, 00:42
oh one day mine will have that sort of treatment :twisted:

Today i bought two lottery tickets, so who knows ;)

But like AlfaJack said, very nice setup :P
And one day.... ;)

Greetings,
Marc

pavs
28-12-06, 08:56
Nice 8)

cuore_sportivo_155
28-12-06, 09:16
What's that strange bump doing in the power graph, around 5100 RPM? It's visible even in the dissipate power graph on the bottom.

Cheers,
Cuore_Sportivo_155

Wolf66
28-12-06, 10:10
Chip is still in developing phase. The "bump" is related to variating boost.

markgq4
03-01-07, 20:16
nice work wolf 8)

Wolf66
03-01-07, 20:38
I made some measurements with G-tech. It showed 420 HP@7000 RPM @1.4 bar boost. I also made acceleration run with datalogger from 100-200 km/h and 100-240 km/h.

100-200 km/h: 9.01 s
100-240 km/h: 17.13 s

The graph shows, that fuelling is still way off, too rich at low rpm and dangerously lean at high rpm. The next step is 3 bar MAP sensor and raising the boost to 2 bar. I already bought the MAP sensor, but mapping the chip is slow process. So far i have changed RPM and Air dens breakpoints to 8000 RPM and 3 bar, but making test runs and logging data in the winter is hard job to do. Car accelerates so fast, that it is difficult to find proper road.


http://www.moj-album.com/slike/5884310/h90_6x3A2QnuCU9j.jpg

Jarkko
04-01-07, 20:49
what turbo do you use ? every detail please .. :D

Juan AR155Q4
05-01-07, 02:46
First, congratulations, you have done a really nice work over there.

Now let's start with the questions:

- Other values of Gtech? (1/4 mile, 0-100 km/h, 0-200 km/h, etc)
- Wich wideband are you using?
- How do you log knock???
- Do you have the diagram for the C&V cams? (lift, ABTDC, etc)
- Where did you got those vernier pulleys? webpage?
- Those injectors are P&P?
- Are you with std ignition system?

Sorry about all these questions, but I'm really astonished with your results.

Congratulations and I really admire what you have done.

Wolf66
05-01-07, 08:30
Thank you.

-I'm currently using some big Holset turbo, because i'm waiting for Garrett GT 30 to arrive.

-I'm using LM-1 Wideband lambda with datalogger.

-I log knock on OEM knock sensor, but i will install additional knock sensor, which is more accurate.

-I'm using C&B road max cams:
Inlet: 15 deg - 55 deg, 10.3 mm lift
Exhaust: 47 deg - 11 deg, 8.4 mm lift

-I bought vernier pulleys second hand, so i don't know, from what shop are they

-I don't know what you mean by P&P injectors. I'm using SIEMENS DEKA 650cc injectors, high impendance, which are direct replacement for OEM injectors

-I'm using std ECU and ignition, apart from 3 bar MAP sensor and injectors.

I couldn't measure 1/4 mile run, because we have winter now and road is constantly slippery. With old engine (330 hp) i measured best acceleration time of 4.4 s.

The chip is still in begining of development phase. Because i changed the MAP sensor, i must recalculate all breakpoints and change all the maps.
I also must add additional RPM breakpoints, because engine is revving to 8000 RPM. My goal is 2 bar of boost and some 550 HP. When i optimize the ECU, i will make new dyno run.

Juan AR155Q4
05-01-07, 11:42
Thanks Wolf for the quick answer.
I really appreciate you share your knowledge with us. If I can help you, be sure IŽll do.

- P&P means Plug & Play. I assume they are for what you said.
- The knock signal you just connected it to an input of the logger? Any filter?
- What do you thing about your experience is the goal for get big HP, cams, FMIC, head work, etc? I know each part makes the hole thing, but wich ones do you thing that makes a big difference?
- I have a Inlet Fiat Tipo cam, what do you thing of this mod?
- Original rods?

Wolf66
05-01-07, 12:31
Yes, injectors are plug&play (but you obviously have to change fuel pressure and fuel maps).

I'm logging the knock sensor without any filters, but at high RPM it can sense other vibrations and produce false readings. I use it only for rough estimations of detonation.

I had tipo cam and oem inlet cam as exhaust cam on my old engine. It made a huge difference. Max power shifted to 6400 rpm and engine happily revved to 7500 RPM. It is great mod for such small amount of money.

All mods are very dependant of each other, the largest power increase made cams+headwork, exhaust system and high boost (large turbo).

I'm using OEM polished rods, which are good for 8000 RPM, or even more with stronger bolts.

Jarkko
06-01-07, 22:53
I'm currently using some big Holset turbo, hmm :( dont you know more ? I had garrett gt40, with smaller t-3 type turbine .63 A/R and with 59 / 65 mm wings. do you know your turbo measurements ?

Wolf66
07-01-07, 21:35
It is Holset H1E, but i don't have any other info, because it is hard to find any tech details about Holset turbos.

Wolf66
11-01-07, 20:29
Here is a short movie of acceleration with new engine. It is still running on 1.3 bar boost, because i didn't have time for writing the new chip yet.

http://www.mobisux.com/album/data/500/42852rolling_start.avi



http://www.moj-album.com/slike/5884310/2pOesDzO7HusBanG.jpg


http://www.moj-album.com/slike/5884310/HWWVx5rIoIv4TQk4.jpg


http://www.moj-album.com/slike/5884310/B_Kd2ZBPMlIwIMB5.jpg


http://www.moj-album.com/slike/5884310/DqxOHtg4YfIWL0VC.jpg

AlfaJack
11-01-07, 22:41
Very impressive!!

but but but, the low oil light!!!!! :shock: :shock: :shock: :shock:

Wolf66
12-01-07, 00:34
Very impressive!!

but but but, the low oil light!!!!! :shock: :shock: :shock: :shock:


He, he, don't worry. As the downpipe is so huge, i had to move the pressure gauge sensor in place instead of low pressure warning light sensor. Because the conector fow low pressure warning isn't connected anymore, the light blinks randomly.

MaxiBoost
23-02-07, 10:45
Wolf ,
good work !

could you give me EGT values ?
when you full trottle ?