View Full Version : 155 Q4 WB :: 1995 Alfa Romeo 155
Alfa romeo 155 Q4 WB :: 1995 Afla Romeo 155 (2011-03-23 23:56:01)
It goes forward :tasty:, Was out for a ride today. The car running fine and are suprisingly good to drive from 1000Rpm, but its all happens from above 3000Rpm. I Have not tested it properly on road, I don't have plats on.
IMG 0355 - YouTube
Some picture of the car on 17" rims, spacers on wheels is 10mm.
The car looks a little bit high without sideskirts.
Thing on to do list:
Remap
Sandblasting and welding were needed under the car
New bushes in powerflex
Mounting of Lester front lip
Air condition service
Bigger breaks .....
Nice five stud wheels...are you planning on fitting them to the 155?
wrinx
The other wheels on the garage wall is for my 159 and 147 GTA. The 17" wheels for 155 is on the last post attachment (black and silver)
Steve Webb
15-03-12, 07:44
Its all starting to come together there. Looks good with those new black/silver wheels. Do you have any spacers on the wheels? The fronts look to fill the arches perfectly but the rears are tucked in a little bit.
In front there is no spacers, but on the rear there is 10mm :eek:. The wheels its not possible to get more out, then the wheels will hit the arces when backseats are loaded.
In front there is no spacers, but on the rear there is 10mm :eek:. The wheels its not possible to get more out, then the wheels will hit the arces when backseats are loaded.
Do not use backseats then :)
Nice cars You've got there, almost exact same setup as mine :)
147GTA, Brera (basically same as 159) and q4
great choices!
regards
WS
I saw that in your garage.
Hello there! Nice choice for your q4's wheels. Which are the rims specs? Are they 7,5J? And what tires size are you running? Thanks.
Cheers,
Cristian.
Hello Xti, its not my choice, they was on the car when i bougth it. Its 7 1/2 J with Yokohama S drive tires. Not the nices rims I have seen but it to expensive to change out for new one
I was taking here out for a test drive today. For the first time I could put the trottle to the bottom. It dose'nt go verry well, but its moving :blink:.
Very nice car indeed. It seems you like turbo machine.
Very nice car indeed. It seems you like turbo machine.
Thanks, i love turbo :happy:
Now it start's to be intresting. Soon I Will have a grate guy over to Norway from England to tune the engine :happy: he is s Well know'n person in the coupe forum for driveable turbo coupe.
I Will fit 305mm brake caliper taken from my 147 Gta . Anybody ho have drawing for bracket's to convert?
Thanks, i love turbo :happy:
Now it start's to be intresting. Soon I Will have a grate guy over to Norway from England to tune the engine :happy: he is s Well know'n person in the coupe forum for driveable turbo coupe.
I Will fit 305mm brake caliper taken from my 147 Gta . Anybody ho have drawing for bracket's to convert?
What's his name?
What's his name?
Sorry for the late respons, his nick is KJ16V i think. Voodoo tuning. After what I have read, he has a good reputiation??
He will be over her for 4 days som it should be planty of time to get it running as it should.
Now the tunning is finnish after a trouble full week. The internal wastegate is to week, and the turbo pressure drops from 1,4 bar to 1,2 bar quikly. We had hoped for 300hk but there is only between 260-280hk :(. I need to get it on a dyno to confirm it.... Anyway the car drives well over 1500Rpm with this race min cam. The tunner thinks this cams makes the car verry slow between 1500-3500rpm, so in the futher i will switch to other cams for better torque
Now the tunning is finnish after a trouble full week. The internal wastegate is to week, and the turbo pressure drops from 1,4 bar to 1,2 bar quikly. We had hoped for 300hk but there is only between 260-280hk :(. I need to get it on a dyno to confirm it.... Anyway the car drives well over 1500Rpm with this race min cam. The tunner thinks this cams makes the car verry slow between 1500-3500rpm, so in the futher i will switch to other cams for better torque
What kind of cams are You using ?
do You have their spec ?
regards
W
What kind of cams are You using ?
do You have their spec ?
regards
W
It's C&B race min cams. Part No.LD16.RM1 Camshafts codesLD16.1090.276C (1)
LD16.088.250C (1) ApplicationRace min Cam lift IN10.9 Cam lift EX8.8 Duration276°/250° Timing30°-66° / 50°-20° Lobe center angles108°/105° Valve lift TDC2.1 / 1.5 Clearance0.35 / 0.40Price (for set)€ 897.00
Steve Webb
28-09-12, 20:40
What Turbo did you go for, because with that sort of setup I would have expected 300bhp to be a conservative estimate.
If you are only getting 260-270bhp I would say that something other than the cams is not right.
Why did you reduce the compression of the engine?
I use the Turbonetics T3/T04e-50 F1-57 .63A/R. The engine was bulid from a recepie of Guy Croft. The compression is verry low because the head gasket is 1,6mm it should be 0,6mm I think (wrong delivery from Walker's).
Another good thing is that the valve don't hit the pistons when (not if) the cambelt snap's . But keep in maind I don't know too mutch about this engine stuff ...
Today I read the engine faults codes with my new bought program. The injection lamp was on. It's show's faulty cam phase sensor (open circiut). Orded a new one today so now I hope the backfire when starting will be solved.
Sorry for the bad English in this thread :lipsrsealed:
It's show's faulty cam phase sensor (open circiut). Orded a new one today so now I hope the backfire when starting will be solved.
Ouch, where did you get that from?
wrinx
Hi hi, I don't want to say it.
They have some pc's left 55 £.
Ok than.
http://www.deltaintegrale.com/catalogue.php?Clv=2&C1=3
Steve Webb
01-10-12, 22:17
Hi hi, I don't want to say it.
They have some pc's left 55 £.
The £55 part (7689407 SEN) only looks like the pick-up for the phase sensor not the whole kit. Is that all you need?
You can chose between only the sensor or the complet unit 220£. It's a little more work with only the sensor but its cheap :thumbsup:
New cam fase sensor is finally in. Some drilling to get it onto the disk, but a easy to nail the new sensor on.
The car is now in a garage of a friend to get some welding.
Juan AR155Q4
28-11-12, 21:12
Today I read the engine faults codes with my new bought program. The injection lamp was on. It's show's faulty cam phase sensor (open circiut). Orded a new one today so now I hope the backfire when starting will be solved.
Sorry for the bad English in this thread :lipsrsealed:Wich program have you used?
I think the name is startrek.
Now are the rust cutted away and new pices is welded in. But best of all, today the snow "arrived". Verry verry fun with 4X4 then
Steve Webb
12-12-12, 19:27
Maybe we ought to look into organizing a special winter get together somewhere with snow. A group of Q4s and a snow\ice track would make for a cracking weekend.
Yes Steve that had been a nice weekend. Some years ago the Norwegian Alfa Romeo club arrange a yearly weekend on a ice track. Unfortunatly I never had time to join them. :wacko: But from the report in the alfa club magazin it was verry verry fun.
Fantastic winter car!
Alfa Romeo 155Q4 - YouTube
Steve Webb
12-03-13, 19:50
Now that looks a lot of fun. I'd prefer a little more run-off though.
Are you just on snow tyres, or have you got a set of studded?
Yes its snow tyres without studd. But when new they are good as studded tyres. In fact this road has up to 17% gradient
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.